Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
Nearly everybody may have their personal rationale with regards to Installing A Bathtub.
Setting up a bathtub isn't specifically brain surgery, however it does require solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately challenging project. If the old tub is readily obtainable, the task can relocate immediately; if you have to open up a wall to get rid of the old tub as well as position the brand-new bath tub, the job is much harder. In either case, the project is within a home handyman's abilities, although you will require a helper to move out the old bathtub as well as set in the new one. Ensure you have qualified on your own for the task as well as are comfortable trying it. Instead of employing a professional to take over a halfway-completed job, it is better to think about utilizing one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This short article will certainly assist you install a brand-new bathtub in your restroom if you have actually currently purchased a brand-new tub and also do not need to alter the plan of your previous water supply pipes.
Your tools and product list should consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome due to the restricted accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin making sure that the washers remain in place between the tap and the sink. Secure the tap in place with the supplier provided backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former kind needs to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bath tub
Making use of the two wood boards under its feet, place the bath tub in the called for setting. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub up until the level checks out degree.
To install taps, fit the bottom of the furthest adaptable tap port to the ideal supply pipe by making a compression join; then do the same for the other faucet.
Activate the supply of water and examine all joints and new pipework for leakages and tighten them if needed. Fill up the bathtub and additionally inspect the overflow electrical outlet and the normal outlet for leakages.
Finally, repair the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the tub ought to wait until the tub has actually been utilized at least once as this will resolve it into its final setting.
Getting ready for the Installation
First of all, the sustaining structure provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets unit to stop strain on the tub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, leading to issues with moisture and feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components and fittings. They are sold in tubes and cartridges, and are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily readily available on the marketplace. It is suggested to fit the tiles using waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that write-up about How to Install a Bathtub Yourself through a good friend on a different site. Sharing is caring. Helping people is fun. Thank you so much for your time invested reading it.
Details Report this page